NFPA® 31 Standard for the Installation of Oil-Burning Equipment 2011 Edition

Chapter 1 Administration
1.1 Scope
1.2 Purpose
1.3 Application (Reserved)
1.4 Retroactivity
1.5 Equivalency
1.6 Units
1.7 Code Adoption Requirements (Reserved)
Chapter 2 Referenced Publications
2.1 General
2.2 NFPA Publications
2.3 Other Publications
2.4 References for Extracts in Mandatory Sections
Chapter 3 Definitions
3.1 General
3.2 NFPA Official Definitions
3.3 General Definitions
Chapter 4 Basic Installation and Operation Requirements
4.1 Scope
4.2 Use of Approved Equipment
4.3 Installation of Oil-Burning Appliances and Equipment
4.4 Electrical Services
4.5 Acceptable Liquid Fuels
4.6 Use of Crankcase Oil and Used Oil
4.7 Temporary Heating
Chapter 5 Air for Combustion and Ventilation
5.1 Scope
5.2 Basic Requirements
5.3 Appliances Located in Unconfined Spaces
5.4 Appliances Located in Confined Spaces
5.5 Combustion Air for Commercial and Industrial Installations
5.6 Louvers and Grilles
5.7 Special Conditions
5.8 Specially Engineered Installations
Chapter 6 Venting of Combustion (Flue) Gases
6.1 Scope
6.2 Basic Requirements
6.3 Draft
6.4 Draft Regulators
6.5 Chimney Connectors
6.6 Chimneys
6.7 Special Venting Systems
6.8 Replacement and Upgrading of Chimneys (Reserved)
Chapter 7 Tanks for Liquid Fuels
7.1 Scope
7.2 Basic Design and Construction of Tanks
7.3 Supports and Foundations
7.4 Installation of Underground Tanks
7.5 Installation of Tanks Inside Buildings
7.6 Requirements for Dedicated Tank Rooms and Tank Enclosures
7.7 Auxiliary Tanks
7.8 Installation of Outside Aboveground Tanks
7.9 Tank Heating Systems
7.10 Special Storage Arrangements
7.11 Tank Leakage Testing and Periodic Inspection
7.12 Abandonment and Removal from Service of Tanks and Related Equipment
7.13 Fuel Storage Systems That Are Permanently Taken Out of Service
7.14 Permanent Abandonment of Underground Tanks
Chapter 8 Heating Fuel Piping Systems and Components
8.1 Scope
8.2 Acceptable Piping — Types and Materials
8.3 Acceptable Fittings — Types and Materials
8.4 Piping System Design
8.5 Tank Fill Piping
8.6 Tank Vent Piping
8.7 Fuel Supply Piping and Return Piping
8.8 Auxiliary Tank Piping
8.9 Piping for Cross-Connected Tanks
8.10 Pumps, Valves, Gauges, and Appurtenances
8.11 Testing of Fuel Supply Piping
Chapter 9 Oil Distribution Systems
9.1 Scope
9.2 Centralized Oil Distribution Systems
9.3 Oil Distribution Systems for Roof-Mounted or Ceiling-Suspended Oil-Fired Units
Chapter 10 Installation of Oil Burners and Oil-Burning Appliances
10.1 Scope
10.2 Basic Requirements
10.3 Posting of Instructions
10.4 Replacement of Appliances and Chimneys (Reserved)
10.5 Operating Controls
10.6 Specific Requirements for Installation of Boilers, Furnaces, Floor-Mounted Unit Heaters, and Water Heaters
10.7 Specific Requirements for Attic Furnaces
10.8 Specific Requirements for Duct Furnaces
10.9 Specific Requirements for Floor Furnaces
10.10 Specific Requirements for Furnaces Used with Refrigeration Systems
10.11 Specific Requirements for Industrial Furnaces and Boilers — Stationary Type
10.12 Specific Requirements for Miscellaneous Heaters (Air Heaters, Salamanders, and so forth)
10.13 Specific Requirements for Recessed Wall Furnaces
10.14 Specific Requirements for Floor-Mounted Restaurant-Type Cooking Appliances
10.15 Specific Requirements for Suspended-Type Unit Heaters
10.16 Specific Requirements for Direct-Vent Appliances (Reserved)
10.17 Specific Requirements for Appliances on Roofs
10.18 Installation of Outdoor Appliances
Chapter 11 Installation and Operation of Oil-Burning Stoves, Kerosene-Burning Room Heaters, and Kerosene-Burning Portable Heaters
11.1 Scope
11.2 Basic Requirements
11.3 Additional Requirements for Kerosene-Burning Portable Heaters
Chapter 12 Used Oil–Burning Appliances
12.1 Scope
12.2 Basic Requirements
12.3 Use of Used Oil–Burning Appliances
12.4 Listing Requirements
12.5 Installation Instructions
12.6 Installation Clearances
12.7 Burners for Used Oil–Burning Appliances
12.8 Venting of Combustion (Flue) Gases
12.9 Used Oil Supply Tanks
12.10 Piping, Pumps, and Valves
12.11 Operating Requirements
12.12 Vent Connector and Chimney Inspection
12.13 U.S. Environmental Protection Agency Regulations
Chapter 13 Oil-and-Gas–Burning Appliances
13.1 Scope
13.2 Listing Requirements
13.3 Installation, Operation, and Servicing Instructions
13.4 Clearances from Oil–Gas-Fired Appliance to Combustible Material
13.5 Construction
13.6 Flue Connections
13.7 Piping, Pumps, and Valves
13.8 Performance
13.9 Testing
Annex A Explanatory Material
Annex B Acceptable Tank Installations (Reserved)
Annex C Typical Chimney and Vent Terminations
Annex D Considerations for Combustion Equipment Firing Alternative (Nonpetroleum) Fuels
Annex E Relining Masonry Chimneys
Annex F Informational References